Crimp Tool Positioners, Turrets & Locators

Crimp Tool Positioners are parts of a Crimping tool designed to adapt the tool frame to a particular application. Available in a wide selection of sizes and shapes locators guarantee versatility of every crimping tool. The data plate on each positioner designates which contacts the positioner accommodates for its wire size and indicates selector position. The positioners are easy to remove and replace when different connector size is required.


How easy crimping tools and positioners, turrets and locators are to use?


They are very easy to use, insert the contact pin into the hole of the crimp tool, load the wire into the contact pin, make sure it’s fully seated then and squeeze until the cycle finishes then finally check that you have a secure crimp.


How do you maintain the product?


There is very little maintenance required for this tool, keep the indenter tips free of debris and dirt.


The Importance of a High-Quality Crimp


When a crimping tool is used on a terminal, two crimps take place at the same time. One is the electrical connection between the conductor and the terminal. The other is the insulation crimp which provides strain relief against vibration and tension.The electrical connection must be gas-tight without any voids between the wire strands and the terminal. If there are any voids present, then corrosion can occur causing resistance and excessive heat which damages the electrical connection. Using a good quality crimping tool will ensure that a full, gas-tight crimp is produced preventing future deterioration of the electrical connection and insulation breakage.


...
Read more Read less

Filters

Viewing 1 - 20 of 158 products
Results per page
Description Price Type Series Number of Contacts Series Number
RS Stock No. 343-2826
Mfr. Part No.TH592
BrandGlenair
HK$2,151.86
Each
units
Turret AF8 - -
RS Stock No. 266-6876
Mfr. Part No.COMP-1
HK$857.83
Each
units
Positioner QM/TNM - -
RS Stock No. 713-3671
Mfr. Part No.VH435
BrandGlenair
HK$1,239.05
Each
units
Turret ITS - -
RS Stock No. 531-425
BrandRS PRO
HK$361.84
Each
units
Positioner QM/TNM 16 -
RS Stock No. 876-2383
Mfr. Part No.525441-5
HK$3,164.11
Each
units
Plug Gauge - - -
RS Stock No. 760-0180
Mfr. Part No.DCE.91.070.3MVM
BrandLemo
HK$1,059.10
Each
units
Positioner M - -
RS Stock No. 314-7629
Mfr. Part No.640035
HK$718.29
Each
units
Positioner AS - -
RS Stock No. 314-7590
Mfr. Part No.TH163
HK$1,746.90
Each
units
Turret M22520/1-04 - -
RS Stock No. 876-2030
Mfr. Part No.169406
HK$83.04
Each
units
Stabilizer CERTI-LOK - -
RS Stock No. 426-3283
Mfr. Part No.K1476
BrandGlenair
HK$1,045.96
Each
units
Positioner K - -
RS Stock No. 674-1707
Mfr. Part No.809-005
BrandGlenair
HK$1,950.86
Each
units
Positioner - - -
RS Stock No. 174-3160
Mfr. Part No.234156-6
HK$1,270.34
Each
units
Wire Crimper - - -
RS Stock No. 174-3161
Mfr. Part No.453819-3
HK$1,379.30
Each
units
Wire Crimper - - -
RS Stock No. 174-3162
Mfr. Part No.690587-1
HK$1,499.34
Each
units
Wire Crimper - - -
RS Stock No. 174-3163
Mfr. Part No.690716-3
HK$1,578.25
Each
units
Wire Crimper - - -
RS Stock No. 721-1434
Mfr. Part No.1208461
HK$635.74
Each
units
Assembly Tool SAC BIT M8-D10 - -
RS Stock No. 864-3368
Mfr. Part No.1583527-1
HK$24,525.16
Each
units
Pneumatic Adapter 626 - -
RS Stock No. 864-3416
Mfr. Part No.3-456406-3
HK$1,310.34
Each
units
Wire Crimper - - -
RS Stock No. 876-2046
Mfr. Part No.303848-2
HK$450.03
Each
units
Pin - - -
RS Stock No. 864-7020
Mfr. Part No.217200-1
HK$24,525.16
Each
units
Crimping Head 626 - -
Related Products
Suitable for main690V nominal voltageIngress protection IP55Full compliance ...
Description:
Suitable for main690V nominal voltageIngress protection IP55Full compliance with BS/EN 60947-3"Padlockable off" handle assembly (3 padlocks up to 8mm dia shank)Supplied with a 3-pole switch body, terminal shroud, extension shaft door interlock and operation assembly (red/yellow emergency switch)Supplied as ...
All have a nominal voltage of 690V. The ...
Description:
All have a nominal voltage of 690V. The stated motor rating utilisation category AC23A/AC3 is for 3 phase 380/440V supply. Padlockable (x4) in "OFF" positionInterlocked in "ON" position to prevent panel door being opened while switch is "ON"
Switch disconnectors are used to isolate electrical equipment ...
Description:
Switch disconnectors are used to isolate electrical equipment before any essential maintenance or repair work can be completed. Switch disconnectors ensure electrical circuits are de-energized safely in accordance with the electricity at work regulations. Engineers and electricians are then able ...
Totally insulated enclosures to IP65Black thumb grip and ...
Description:
Totally insulated enclosures to IP65Black thumb grip and grey front plate, emergency stop versions have a red thumb grip and yellow front plateSurface mounting.