Time Electronic 7006 Current Loop Calibrator 20mA

Product overview and Technical data sheets
Legislation and Compliance
RoHS Status: Not Applicable
COO (Country of Origin): GB
Product Details

Time Electronics Loop-Mate 1 & 2 Current Loop Calibrator

Loop-mates designed for the calibration, testing and measurement of process loops are pocket sized units that boast a simplistic operation, no complicated selections just grab and go.
Loop-Mate 1 (537-2580) - Simulator which acts as a source in providing loop signals, a simple up and down button allows the user to increase or decrease the signal.
7 set points: 10%, 25%, 50%, 75%, 90% and 100% each of which is shown on LED's with beeps. The Loop-Mate 1 when used in conjunction with Loop-Mate 2 allows users to check a signal has arrived within specification at another location.

Loop-Mate 2 (537-2603) - Signal indicator with a 4-20 mA or 0-10 V loop type selection, also allowing the user to choose between a display of direct units or % of span. Also, specifically designed so that the LCD display shows the signal in mA, V, or % of span within an accuracy of 0.05%.

Powered by a PP3 battery both units provide up to 40 hours of continuous use, making them the ideal addition to any engineer testing kit.

Features and Benefits Loop-Mate 1:

• 0.1% Accuracy
• TxSim or RxTest mode
• 25 mA max loop supply
• 140 x 65 x 30 mm dimensions

Features and Benefits Loop-Mate 2:

• 4-digit LCD display
• 0.05% accuracy
• RxSim, TxTest, 50mA/50V measure
• 140 x 65 x 30 mm dimensions

FAQ's

What is a current loop calibrator?

Current loop calibrators are specially designed instruments for current loop trouble shooting, testing and calibration. They can source current on unpowered devices in a loop, simulate the operation of loop powered transmitters and also measure current. These calibrators often feature time saving technology, specialist graphics using digital interfaces and micro-processor based electronics.

How much current flows in each loop of a parallel circuit?

Determined by Ohm's law, which states that the current between 2 points through a conductor is directly proportionate to the voltage across those 2 points, divided by the resistance of the conductor. I = V/R. This is also the case for series and parallel circuits, however in parallel circuits the total current can be affected by the way the resistors have been connected, as well as their ohmic value. Current does divide up and there can be more current in one area over another nonetheless when all areas are added up the total amount is the same.

Note

Loop-Mate 1 is a simulator
Loop-Mate 2 is an indicator

Supplied with

Carry case, leads and technical manual

Loop-Mate1 generates 4 to 20 mA or 0 to 10V to simulate loop signals. Audible beeps that change pitch in sympathy with the output level plus auto-stepping through the range simplify a calibration engineer’s job. It has several additional features - it can generate the current using its own internal supply (RX Test mode), or control the current using an external supply (TX Sim mode).

TxSim and RxTest

Specifications
Attribute Value
Absolute Maximum Current Measurement 20mA
Best Accuracy ±0.1 %
Battery Type PP3
Battery Life 40 h
Power Source Battery
Dimensions 30 x 65 x 140mm
Weight 180g
Height 140mm
Length 30mm
Maximum Operating Temperature +50°C
Minimum Operating Temperature -5°C
Width 65mm
Model Number p 7006
37 In stock for delivery within 3 working days
Price Each
HK$ 2,708.51
(exc. GST)
units
Per unit
1 +
HK$2,708.51
Related Products
Permanent pull loops for AMP-LATCH IDC ribbon cable ...
Description:
Permanent pull loops for AMP-LATCH IDC ribbon cable receptacle and pin connectors. These pull loops are made from natural colour PVC, 94-VTM-1 rating. For details of connectors that these pull loops can be used with please see additional data table. ...
These connectors provide fast reliable mass termination to ...
Description:
These connectors provide fast reliable mass termination to Speedbloc® ribbon cable without the need to separate individual wires before assembly. No cable stripping, soldering or expensive tooling is requiredFully compatible with conventional D connectors and accepts all standard locking systemsLow ...
From ERNI, this TMC series of sub-miniature d-built ...
Description:
From ERNI, this TMC series of sub-miniature d-built connectors are designed for use with ribbon cables. With 9, 15, 25, 37 pin connectors available, the series also offers appropriate strain relief and connector screws for reliable interfacing. The trapezoidal design ...
From 3M, this range of 101 Series Mini ...
Description:
From 3M, this range of 101 Series Mini D Ribbon (MDR) Connectors are .050" IDC Wiremount Shielded Plugs. The design of the 101 Series Mini D Ribbon (MDR) Connectors, provides IDC terminations for the individual cores and wiper-on-wiper contact. The ...